In addition to high-quality design and exquisite production process, it is also very important to choose a suitable installation method for an advertisement signboard. The installation mode must be selected according to the characteristics of the billboard and the installation environment. Next, Jinan sign production company will check 8 common installation methods in advertising signs for you!
1粘貼式
1 paste
粘貼式應用范圍廣泛，常用的粘合膠有玻璃膠、泡沫膠、結構膠等。要根據廣告標識材質及安裝環境、內外干濕、溫差等各種情況綜合考慮，選擇合適的膠粘劑。發光字運用很多的粘貼方式是玻璃膠安裝，像樹脂字、無邊字、注塑字都可選擇玻璃膠粘貼式安裝。
The adhesive type is widely used. The commonly used adhesives are glass glue, foam glue, structural adhesive, etc. It is necessary to select the appropriate adhesive according to the advertising sign material and installation environment, internal and external humidity, temperature difference and other conditions. There are many ways to paste the light-emitting words, such as resin words, borderless words and injection words.
2粘貼吊掛式
2 paste hanging type
適用于一些折邊標識。如果安裝墻體基礎是大理石、玻璃、不銹鋼這類不允許打孔，而且又堅固平整的安裝墻，那這種方法是很適合不過的了。準確測量好安裝位置，以防把標識裝歪，用AB膠將有機邊條或角鋁等材料粘在墻體上，然后將標識折邊掛上，微調位置，用玻璃膠固定即可。
It is suitable for some hem marks. If the installation wall is based on marble, glass, stainless steel, which is not allowed to drill, but also solid and flat installation wall, this method is very suitable. Firstly, the installation position shall be measured accurately to prevent the sign from being installed askew.
3吊掛固定式
3 hanging fixed type
這是針對一些折邊標識，體積較大、質量重、用泡沫填充粘貼無法安裝所采用的方式。確定打孔點，用沖擊鉆打孔，釘上膠塞及自攻螺絲。只用一只螺絲時，必須在標識標牌的上沿中間部位打孔，以保持水平，然后將標識折邊掛在螺絲上，調整位置后，四周封上玻璃膠固定即可。
This is for the use of some flanging labels, large volume, heavy weight, with foam filling and paste can not be installed. First, determine the drilling point, use the impact drill to drill holes, screw on the rubber plug and self tapping screw. When only one screw is used, holes must be drilled along the middle part of the upper edge of the sign plate to keep it horizontal. Then, hang the sign hem on the screw. After adjusting the position, seal the glass glue around to fix it.
4底板內部打螺絲式
4 screw type inside the bottom plate
這種安裝方法針對于金屬底盒的標識，如吸塑字、平面發光字這類標識。安裝時先根據測量的尺寸在安裝墻及標識金屬底板上鉆好孔，將底盒用螺絲固定于安裝墻上，再將字殼用螺絲安裝于底盒上面。
This installation method is for the identification of metal bottom box, such as blister type, flat light-emitting type. During installation, first drill holes on the installation wall and mark metal base plate according to the measured size, fix the bottom box on the installation wall with screws, and then install the word case on the bottom box with screws.
5懸掛式
5 hanging type
這種方式所采用的吊鏈材料主要有鐵鏈、鋼索、吊魚絲、扎帶等。可根據室內外環境、標識標牌制作重量及其它一些特殊要求采用合適吊裝材料。吊牌燈箱通常就是運用這種安裝方法。
The chain materials used in this way mainly include iron chain, steel cable, fish hanging wire, tie belt, etc. Suitable hoisting materials can be used according to indoor and outdoor environment, production weight of signs and other special requirements. This installation method is usually used for the pendant light box.
6落地式
6 floor standing
根據設計要求，將標識放置于相應位置即可。金屬雙面字大部分以落地式的方式安裝。
According to the design requirements, the logo can be placed in the corresponding position. Most of the double-sided metal characters are installed in a floor type way.
7填埋式
7 landfill type
適用于地面為土壤結構，標識不需要移動的情況。根據標識的大小、高低來確定要挖的坑的大小以及所需要用到的混凝土的多少。宣傳欄、導視牌大部分都運用這種方式安裝。
It is applicable to the situation that the ground is soil structure and the mark does not need to be moved. According to the size and height of the sign, determine the size of the pit to be dug and the amount of concrete to be used. Most of the billboards and guide boards are installed in this way.
8螺桿安裝式
8 screw mounted
螺桿安裝是在標識的底板上焊接有一定長度的螺桿，安裝墻面有相應的安裝孔，安裝時標識的螺桿直接插入對應的安裝孔固定即可。螺桿安裝是為了使標識離安裝墻面之間具有一定的間距。在發光字中，背打光字基本都是運用螺桿安裝，這是考慮到它本身的發光特性。
Screw installation is to weld a certain length of screw on the marked bottom plate, and install the wall with corresponding installation holes. During installation, the marked screw is directly inserted into the corresponding installation holes for fixation. Screw installation is to make the mark have a certain distance from the installation wall. In the light-emitting words, the back type light words are basically installed by screw, which is to consider its own light-emitting characteristics.
其實，廣告設計制作中標識標牌制作的安裝方法是非常靈活的，要根據實際安裝情況而定。對于一些安裝環境與自身機構都比較復雜的標識，往往需要多種安裝方法結合使用才能完成安裝。濟南標識標牌制作公司的分享就到此結束，更多干貨內容，敬請濟南標識標牌制作公司官網https://www.www.tb10.cn！
In fact, the installation method of logo and sign making in advertising design and production is very flexible, which should be determined according to the actual installation situation. For some signs with complex installation environment and its own mechanism, it often needs a variety of installation methods to complete the installation. This is the end of the sharing of Jinan logo production company. For more dry goods, please visit the official website of Jinan logo production company https://www.www.tb10.cn !
